
Page 25
Installation and Technical Application Guide
H
NB
TM
D
igital multimedia mixer for Audio, Video and Wireless applications
LEFT
SLOT
(HB-2PA)
‘J1’
Note: HB-2PA Preamp card
ALWAYS fits into the LEFT SLOT
of either HNB-A or HNB-B units
HNB-A Chassis
(inside front view)
HNB-B Chassis
(inside front view)
LEFT
SLOT
(HB-2PA)
‘J1’
HNB-A
[ AUDIO ONLY SYSTEM ]
HNB-B
[ AUDIO - VIDEO - IR SYSTEM ]
IMPORTANT NOTE: Whenever the HNB-A is combined with HNB-B and the IR Remote Control
function is utilized the HB-2PA Preamp module MUST MOVE to the HNB-B unit LEFT SLOT.
HB-2PA
VOL
P
WR
B
ASS
TREBLE
[B]
C]
A
B
C
[A] = INTERNAL SOURCE
MIC
VOL
HB-2PA PRE AMP
Á
Â
of either HNB-A or HNB-B units
AUDIO - VIDEO - IR SYSTEM ]
AUDIO - VIDEO - IR SYSTEM ]
Preamp module MUST MOVE to the HNB-B unit LEFT SLOT
A Preamp module MUST MOVE to the HNB-B unit LEFT SLOT
Preamp module MUST MOVE to the HNB-B unit LEFT SLOT
is combined with HNB-B and the IR Remote Control
Whenever the HNB-A is combined with HNB-B and the IR Remote Control
Preamp module MUST MOVE to the HNB-B unit LEFT SLOT
is combined with HNB-B and the IR Remote Control
Preamp module MUST MOVE to the HNB-B unit LEFT SLOT
Preamp module MUST MOVE to the HNB-B unit LEFT SLOT.
is combined with HNB-B and the IR Remote Control
SECTION 6.1 - HB-2PA PREAMP CARD: LOCATION AND INPUT ADJUSTMENTS [ HNB-A / HNB-B ]
IR IN (2+3)
HB-2PA PREAMP
(1+2)
3-POSITION HEADER
1
2
3
LEFT
SLOT
(HB-2PA)
HNB-A Chassis
(inside front view)
HNB-A
[ AUDIO ONLY SYSTEM ]
IMPORTANT NOTE: The jumper MUST be in the 1+2 position of JP1 and JP2 when the
HB-2PA preamp card is used in HNB-A (LEFT SLOT, ‘J1’),
(1+2)
JP1 + JP2
Á
Â
preamp card is used in HNB-A
A preamp card is used in HNB-A
preamp card is used in HNB-A
preamp card is used in HNB-A (LEFT
MUST be in the 1+2 position of JP1 and JP2
MUST be in the 1+2 position of JP1 and JP2
MUST be in the 1+2 position of JP1 and JP2
HB-2PA ‘DUCK’ Override initiates an automatic ‘DUCK’ of the HNB-B
audio sources (B+C on Front) and is adjustable from 0dB to -50dB (Off) at
10ms attack time when signal is detected and releases at 3-5 seconds
when signal is removed. This is an internal screwdriver manual ‘POT’
adjustment on the HB-2PA and is not normally end-user accessible.
Note: When the internal audio line input is activated and ‘Voltage Present’ is
detected, all audio sources (B + C) to HB-2PA are immediately ‘DUCKED’
to the amp and speakers. The audio line signal routes to the amp and is
broadcast to speakers ‘ON TOP’ of the original audio source. The input
audio level IS ADJUSTABLE and can be set different than the original
source material.
6.2 HB-2PA Preamp card: Input Adjustment, DUCK override adjustment, Location
SonicDevices n 9950 Baldwin Place, El Monte CA 91731 n (T) 626-454-8169 n (F) 626-433-1079 n (W) www.sonicdevices.net
Sansonic HNB A+B+C installmaULb:Sansonic HNB A+B+C installmaULb 6/29/11 6:39 PM Page 25
Comentarios a estos manuales