Sansonic HNB-B Guía de instalación descargar pdf (Pagina 34)

SonicDevices n 9950 Baldwin Place, El Monte CA 91731 n (T) 626-454-8169 n (F) 626-433-1079 n (W) www.sonicdevices.net

Installation and Technical Application Guide

igital multimedia mixer for Audio, Video and Wireless applications

Page 34

Transmitter

7.7 HB-RU Assisted Listening Receiver - Normal Mode - Translation Mode

Transmitter

Normal Broadcast

(Up position)

Translation - Channel 2

(Down position)

Step 1: Once system is operational, place front slide

switch on HB-Tx card in DOWN position to

ranslation - Channel 2 mode. Note

Channel 2 is always the SM1 hand-held

microphone. When slide switch is placed in

this position; the SM1 microphone output is

MUTED (OFF) from the overhead speakers

connected to HNB-A and its output is only

transmitted to the HB-RU Receiver.

Step 2: To select Channel 1 (Teacher micro-

phone: TM1, TM2, TM3) or Channel 2

(Student microphone: SM1, PRESS AND

HOLD for (5) seconds the Volume (+) for

Channel 1 or the Volume (-) for Channel

The slide switch for NORMAL BROADCAST mode is in the UP position. The slide

switch for TRANSLATION - CHANNEL 2 is in the DOWN position. For Normal and

ranslation modes, both Channel 1 and Channel 2 are broadcast to the HB-RU unit

simultaneously. All HNB-A audio sources are transmitted to the HB-RU.

Right side

Left side

airing

utton

R Lens

olume (

/ Channel 1

olume (

/ Channel 2

Volume / Channel

election

HB-RU Receiver

HB-Tx Transmitter Module

(close-up of slide switch)

Right side

Left side

Pairing

Button

IR Lens

Volume (+) / Channel 1

Volume (-) / Channel 2

Volume / Channel

Selection

HB-Tx Transmitter Module

(close-up of Power/Pairing)

FINAL INSTALLATION CHECK OUT FOR HNB-C WIRELESS WITH

HB-Tx. If after normal operation of HB-Rx connected microphones, an

intermittent noise, or 'drop out' is noticed AFTER the HB-Tx is installed

and operating; it is recommended to change the HB-Tx 'ID' frequency as

shown below in steps 1-3. Once 'ID Change' is accomplished TM Series

and SM1 microphones should operate in Normal mode.

Step 1: In the power off mode for the HB-Tx module, PRESS BOTH

POWER AND PAIRING button down for 3-5 seconds until the

LED starts a steady RED flash rate.

Step 2: PRESS PAIRING button on HB-Tx module for 2-3 seconds

to achieve FAST 'PAIRING ACTIVE' rate on the LED.

Step 3: Turn ON the HB-RU Receiver and then press the PAIR-

ING' button on the HB-RU for for 2-3 seconds to achieve

'FAST' FLASH rate on the LED and face the HB-RU

towards the HB-Tx module LED window lens. Note: Both

units must be within 1M / 3ft. Once channel ID is com-

plete, the LED on both HB-Tx and HB-RU will begin a

'STEADY BLUE' state. See section 7.3

7.8 Final Test for HNB-C Wireless When using HB-Tx Transmitter

Sansonic HNB A+B+C installmaULb:Sansonic HNB A+B+C installmaULb 6/29/11 6:40 PM Page 34

1 2 ... 29 30 31 32 33 34 35 36

Comentarios a estos manuales

Sin comentarios

Sansonic HNB-B Guía de instalación Pagina 34

Comentarios a estos manuales

Relacionado con productos y manuales para Amplificadores de audio Sansonic HNB-B